Print4Sure EuroForm IPDS 100 Guia de Instalação

EuroForm DIMM Installation Guide English For HP LaserJet Printers

- 10 - Remove the new DIMM from the antistatic package. Hold the DIMM with your fingers against the side edges and your thumbs against the back

- 11 - HP LaserJet 4200 and 4300 CAUTION Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or fr

- 12 - Remove the DIMM from the antistatic package. Hold the DIMM with your fingers against the side edges and thumbs against the back edge. Al

- 13 - HP LaserJet 9000 CAUTION Static electricity can damage DIMMs. When handling DIMMs either wear an antistatic wrist strap or frequently t

- 14 - Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a

- 15 - HP LaserJet 9000mfp CAUTION Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or frequent

- 16 - Press the DIMM straight into the slot (press firmly). Make sure the locks on each side of the DIMM snap inward into place. (To remove a

- 17 - HP Color LaserJet 3700 CAUTION Static electricity can damage DIMMs. When han-dling DIMMs, either wear an antistatic wrist strap, or

- 18 - Remove the DIMM from the antistatic package. Lo-cate the alignment notches on the bottom edge of the DIMM. Holding the DIMM by t

- 19 - Reconnect the power cable and USB/parallel cable. Turn the printer on.

- 2 - Installation Guide NOTE • The information contained in this document is subject to change without notice. • EuroForm makes no war

- 20 - HP Color LaserJet 4600 CAUTION Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap, or fr

- 21 - Slide out the formatter board and set it on a clean, flat, grounded surface. Release the locks on each side of the DIMM slot.

- 22 - Firmly press the DIMM straight into the slot. Close the locks on each side of the DIMM until they snap into place. Align the

- 23 - HP Color LaserJet 5500 CAUTION Static electricity can damage DIMMs. When han-dling DIMMs, either wear an antistatic wrist strap, or fr

- 24 - Release the locks on each side of the DIMM slot. Remove the DIMM from the antistatic package. Locate the alignment notches on the b

- 25 - Reconnect the power cable and interface cables, and turn the printer on.

- 26 - HP Color LaserJet 9500 CAUTION Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or frequ

- 27 - Press the DIMM straight into the slot (press firmly). Make sure that the locks on each side of the DIMM snap inward into place. (To re-m

- 28 - Notes:

- 29 -

- 3 - Caution DIMM boards and your printer formatter board can be damaged by small amounts of static electricity. When handling a DIMM or other

- 30 -

- 31 - Support If you experience problems with DIMM installation or you have other questions, please send an email to [email protected]. However,

- 32 - EuroForm A/S technologies have created a range of solutions that integrate with Hewlett-Packards LaserJet and Color Lase

- 4 - Table of Contents Table of Contents...

- 5 - HP LaserJet 2300 CAUTION. Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or frequently

- 6 - Remove the DIMM from the antistatic package. CAUTION. To reduce the possibility of damage caused by static electricity, always wear an el

- 7 - HP LaserJet 4100 CAUTION Static electricity can damage dual inline memory modules (DIMMs). When han-dling DIMMs, either wear an ant

- 8 - Remove the DIMM from the antistatic pack-age. Hold the DIMM with fingers against the side edges and thumbs against the back edge. Align t

- 9 - HP LaserJet 4100mfp CAUTION Static electricity can damage DIMMs. When handling DIMMs, either wear an antistatic wrist strap or frequent